To view this as a web page, click here

 

 
 
 
 
 

April 19, 2021
Safety Tip of the Week delivered to your inbox each Monday by GrainnetSafety.com


Dust Suppression Techniques

Choosing The Right Method of Suppression Can Minimize Hazards

Mitigating the presence of grain dust is a crucial part of any housekeeping program to comply with Occupational Safety and Health Administration (OSHA) standards and risk management practices, such as loss control. These tips highlight tools that can be used to assist in dust mitigation.

OSHA can currently levy grain dust citations at a grain handling facility under three separate standards for housekeeping violations.

These include OSHA's Grain Handling Standard (29 CRF 1910.272), which directly addresses grain dust hazards.

Further, in 1910.22(a)(1), which applies to walking working surfaces, the agency contends that it continues to "interpret" combustible dust (which is not formally defined) as a walking working surfaces hazard since excessive accumulation is considered a slip, trip, or fall hazard.

Finally, 5 (a)(1), the General Duty Clause, requires employers to provide a safe work environment.

In addition, NFPA 61, Standard for the Prevention of Fires and Dust Explosions in Agricultural and Food Processing Facilities, is the primary voluntary consensus standard focused on the grain handling industry.

Compliance with NFPA standards is not required under the OSHA grain handling facilities standard (29 CFR 1910.272). Instead, NFPA standards are voluntary and only apply to facilities if local authorities have adopted the standards within their jurisdiction, i.e. fire marshals may adopt the standards and rely on them for enforcement purposes. The NFPA standard specifically focused on mitigation and prevention and management systems.

Oils Used For Dust Suppression

The industry primarily uses white mineral oil to reduce the concentrations of dust near potential ignition sources within grain elevators. Food grade soy oil also is an effective dust suppressant, but its use may be limited by its potential rancidity, flow characteristics in the cold weather, and cost.

White mineral oil meeting Food and Drug Administration-established specifications may be used safely in food applications as a dust-control agent for wheat, corn, soybean, barley, rice, rye, oats, sorghum at a level of no more than 0.02 percent by weight of grain [200 parts per million (ppm)].

In addition, white mineral oil meeting the established specifications and with ISO 100 oil viscosity may be applied as a dust-control agent for rice at a level of not more than 0.08 percent by weight of the rice grain (800 ppm) (21 CFR 172.878).

Dust suppression oil usually is applied to grain at receiving and shipping legs, as well as at load out spouts. In some cases, it will cause the dust particulates to stick to whole kernels within the grain stream.

Normally, white mineral oil is applied at a rate of 1.2 to 1 gallon per 1,000 bushels (approximately 60 to 110 ppm).

The use of dust suppression oil requires that a dust control system draw the oil from a supply tank to an internal pump, which in turn, supplies oil to the system's pressure controls and then directly to the spray assemblies.

Dust Collection Systems

Dust collection systems capture the particulates and store them until they can be disposed of or reintroduced to the commodity.

These systems operate very much like a large-scale vacuum cleaner. Powerful fans create the suction that transports the dust particles through duct work to the collector.

There are several types of dust-collector systems.

A cyclone-style collector will push air through the top of the collector that then pushes the dust downward. The dust then will hit the sides of the collector while the clean air is forced out into another filtration system to collect the finer particles. The larger dust collected by the cyclone then is moved away from the system via gravity or any other engineered system to a storage receptacle.

Baghouse-style collectors have many different sizes and designs; but all operate in the same basic way. The dust-laden or particle-laden air stream enters the baghouse through the dirty air inlet. It then travels along the surfaces of multiple fabric tubes (bags), and then basses outward or inward through the fabric.

The larger particles fall down into a hopper while the smaller particles accumulate on the fabric tube surfaces. A cleaning mechanism occasionally cleans the particles from the tube, which then also fall into the hopper. This cleaning mechanism typically is a compressed air solenoid device set to fire in sequence as the dust suppression system is in operation. The clean air then exits from the top of the baghouse.

Point-of-Use collectors have increased in popularity in the past decade. They work similar to the other collectors, with airflow being the means of transport for the dust. These systems are installed where the bulk of the dust is created, such as dump pits, legs, shakers, and distributor floors.

The manufacturer or engineer will help in an onsite assessment of a facility's best installation sites. Improvements have been made to the filtration medium, allowing for maximum airflow.

Options for a point-of-use system may limit duct work. Some systems will have the exhaust system flow to another centralized baghouse to reclaim the particulate; others simply have an agitator or compressor in place to knock the product off the filter and back into the grain stream.

Choosing The Right Method of Suppression Can Minimize Loss

As part of OSHA's Grain Handling Hazard, every grain handling facility is required to develop and implement a written housekeeping program. An effective housekeeping program may not only help to reduce safety risks, but also may control expenses that could affect a firm's ability to compete in the marketplace.

However, it may not be feasible to collect all dust using manual housekeeping methods; therefore, in some cases it may be necessary to utilize a dust-collection system.

Prior to installing a new dust suppression system or overhauling an existing one, the source(s) for the dust need to be identified. Next, the amount of dust created through internal practices, such as unnecessary bin transfers or drying temperatures, should be mitigated.

Remember: Never substitute a proper housekeeping and inspection plan with a machine!


Source: National Grain and Feed Association (NGFA), Arlington, VA, 202-289-0873.

For more information, please contact Jess McCluer, VP of Safety and Regulatory Affairs, or Jim Seibert, Director of Safety, Education, and Training.

This Safety Tip of the Week was originally published on May 14, 2018.

 
 

 

Follow Our Safety News on Twitter

Receive Our Safety E-News Twice a Month

Safety Tip of the Week Archives

 

Safety Tip of the Week is edited by Digital Media Specialist John Reidy and published each Monday by Grain Journal, Decatur, IL

800-728-7511 | Website: grainnetsafety.com